Wincor Nixdorf BA73A-2 User Manual

BA73ALCD TFT 15" (38.1 cm) Flat ScreenUser Manual

Unpacking and checking the Delivery UnitUnpack the parts and check to see whether the delivery matches the infor-mation on the delivery note. The deli

BA73A ComponentsScreen ModuleThe screen module represents the main unit of the BA73A. It comprises ofa TFT-LCD colour screen, the TFT-interface and an

“Stretching” is only possible when a separate LCD controller or an adapter(“PanelLink-Bridge”)isused(“D1" Central Processing Unit with Celeron or

The LCD-Controller-A/BA73A is a plug-in-controller with a PCI-interface.There are two connections fora 40-pin MDR connector with integrated COM5 outpu

Panel of LCD- Ccontroller-A/BA73ABoard layout (LCD-Controller-A/BA73A)Jumper Settings of the LCD-Controller-A/BA73A:B1: OPENB2: ClosedB3: Closed112405

Capacative Touch Screen (Option)GeneralThe TFT Touch Screen works according to the principle of a change inanalog capacitance. It has a glass screen w

The programming interface of the screen is identical to the mouse inter-face. Touch ScreenTouch Screen and Sleep ModeUsing the Touch Screen with a BEE

How to OperateThe Touch Screen responds to the slightest contact, therefore you do nothave to apply much pressure when working with the screen. This d

I/O-Addresses of COM InterfacesCOM BoardThe four COM interfaces of the COM board have the followingI/O-addresses. Please refer to the table for the ju

The interrupts IRQ9 and IRQ10 are added for PC application only. For acorrect reproduction of the interrupt signals it is necessary that the jumperIR9

Published byWincor Nixdorf GmbH & Co. KGD-33094 PaderbornBestell-Nr./Order No.: 01750038094APrinted in Singapore

Assignment of COM port addresses and interrupts (installation details)Ensure that there is no conflict of hardware port addresses or interruptrequests

IRQ12, most likely conflict Mouse Port or PS/2 MouseThese types of mice are supported by Windows NT through theI8042PRT.SYS driver. The mouse usually

The AT COM Board manual numbers the COM ports from 5 to 8. The ori-gin of this numbering is from the BEETLE, which has COM1 to COM4 onthe motherboard.

This will be impossible for hardware reasons! The problem is, that in sucha case on the AT bus two different hardware instances would be fightingfor t

Using shared interrupts for COM ports under Windows 95Under Windows 95, sharing COM ports doesn’t require special provisionsother than correctly speci

Board layout COM boardCOM7COM 5 /COM 6COM81122Interrupt JumperInterrupt RequestI8 I1I9I16IR15IR12IR11IR10IR 9IO 3IO JumperIO 1COM BoardGB - 18

LCD-TFT Adapter A-Celeron/Pentium IIILCD-TFT Adapter A-CeleronIf your BEETLE is equipped with a“D1" or ”D2" CPU the TFT adaptercan be connec

Resistive Touch Screen (Option)GeneralThe resistive TFT Touch Screen is constructed of a hard-coated polyestertopsheet that is overlaid on a conductiv

Construction of the resistive Touch Screen:How to OperateTouching the touch screen has the same effect as clicking the left mousebutton. You only need

Cleaning InstructionsAlways turn off the system before cleaning. The surface of your TouchScreen should be cleaned with a water-based solvent or a non

BA73ALCD TFT 15" Flat ScreenUser ManualEdition May 2001

Installing and Securing the Screen into PlaceThe screen can be easily installed as a table top terminal.Securing into PlaceRemove the footedstand and

Now fasten the screwon the footed standinto place again usingthe crosstip screw-driver.Ensure that the screwis in the correctposition.Securing into Pl

Adjustable Screen AngleAdjustable Screen AngleThe BA73A is fitted with a joint on the rear. You can optimize the angle ofthe screen depending on the v

Ergonomic Terminal WorkplaceErgonomic Terminal WorkplacePlease observe the following when setting up your terminal workplace:Avoid direct glaringand r

InstallationInstalling the Controller in the BEETLEFirst ensure that the controller is switched off and the mains supplyplug has been pulled out.Remov

In order to be able to install the LCD-Controller-A, you must first removethe metal panel that covers the free slots by loosening the screw.Set the ju

Connecting the Speaker CableConnecting the Speaker CableRemove the speaker cable from the BEETLE-CPU by simply unpluggingthe connector. The BEETLE spe

Connecting the BA73A to the BEETLE /20The hardware installation is carried out according to the installation of theBA73A to the BEETLE. When installin

Connecting the BA73A to the PCConnecting the BA73A to the PCFirst ensure that the controller is switched off and the mains supplyplug has been pulled

The touch function with a LCD TFT adapter-A has to be activated viaa jumper.The COM2 interface has to be covered and may no longer be usedexternally.T

Copyright © Wincor Nixdorf GmbH & Co, KG, 2001The reproduction, transmission or use of this document or its contents is not permitted withoutexpre

Jumper SettingOne jumper of the PT-jumpers is used to define the size of the TFT moni-tor: 12" and 15".12" monitor connected15" mo

The Jumper layout of the Celeron/Pentium III “D1"- board+-AD1816AJSPS2/MouseMICKYB/ECOM4*COM3*USBCOM2*/ICOM2*COM1OUTCD-AUDIOAUDIO69000VGA/TFTPCI/

COM2 with Celeron/Pentium III Board (“D1"-CPU)COM2 for peripheralsCOM2 for touch function ussing a TFT adapterIf the BEETLE is delivered with TFT

Connecting the cableThe data cable is to be connected with the 50-pin connector of the TFTadapter. Take care that the thickening of the cable (Ferrit)

Now plug in the cableuntil it snaps in (see il-lustration).When removing thecable press on theconnector release.Installing a LCD-TFT Adapter ANever op

Inserting the CableInserting the CableThe cable cover is lo-catedinthebaseplate.Lift the cable cover .Pull the cable coverforward in the directionof t

Releasing the Cable ConnectionReleasing the Cable ConnectionNever remove a cable from a connector socket by simply pulling on thecable. Always remove

Software InstallationThe software installation refers to the installation of corresponding displaydrivers; the installation of the touch screen compri

Software InterfacesTouch ScreenTouching the screen corresponds to press the left mouse key. The touchscreen programming interface is identical to that

Automated Logic Diagram (ALD) and PinAssignments7413140pin. MDRKYBDBEETLE-CPUSPKCOM4 COM3 COM2 COM1COM640pin MDRFREE ISA-SlotCOM7*COM8*LANSignals: TFT

ContentsIntroduction ... 1From Point-of-Sale to Point-of-S

InterfaceAutomated Logic D iagramThe LCD interface is connected to the TFT controller via a 40-pin cable.The inverter, LCD display, touch screen contr

Pin AssignmentsBA73A Connectors of the 40-pin TFT Interface Pin AssignmentPIN # Signal PIN # Signal1 HUOUT 2 RXCN3 GND 4 RXCP5 P5VLCD 6 P5VLCD7 RX0N 8

COM 6 Interface of the LCD-Controller-A/BA73APIN # signal1 P12VF2RxD23TxD24DTR25 GNDF16DSR27RTS28CTS29P5VFInternal Speaker Connector for Controller an

Internal Connecting SocketPIN# COM7 COM81P5VF P5VF2 GNDF GNDF3 DCD3 DCD44 GND GND5 CTS3 CTS46 DTR3 DTR47 RTS3 RTS48 TxD3 TxD49 DSR3 DSR410 RxD3 RxD411

External Connecting SocketPIN# with power supply w/o power supply1 +12V DCD2RxD RxD3TxD TxD4DTR DTR5 GND GND6DSR DSR7RTS RTS8CTS CTS9+5V RIPin Assignm

Technical DataThe following operating conditions are valid for a BA73A TFT that is fittedwith all the available modules.Climate classIEC 721 3/3 Class

TFT/ LCD ScreenTFT/LCD ScreenFrequenciesHorizontal (KHz) 48.3Vertical (Hz) 60SolutionsHorizontal 1024 pixel (XGA)Vertical 768 lines (XGA)Colour RGB 16

BA73ADimensionsScreen size 15" (38.1 cm)Active screen size(horizontal x vertical)304.1mm x 228.1mmCable length 3 m / 5mDimension Display Housingw

Current ConsumptionCurrent ConsumptionLCD-Controller-A/BA73ANormal Mode: 400 mA + 5VStandby Mode: 300 mA + 5V50 mA +12V30 mA -12VScreen ModuleConsisti

LCD-Controller-A/BA73AInterfacePCI, 32 BitModeXGAResolution1024 x 768 (High Color)Image Repeat Memory2MBScreen MemoryText modePage modeLinear modeB800

Resistive Touch Screen (Option)...20General...

COM BoardCOM-Board ControllerSystem interfaceISA, 8 MHzI/O-addresses forCOM interfaces3 address records 2E0, 330, 320 thatcan be set by jumperInterrup

Manufacturer’s Declaration and ApprovalGeneral AuthorizationThis device fulfills the requirements of the EEC standard89/336/EWG “Electromagnetic Compa

Tested SafetyThe BA73A has been awarded theGS symbol for “Geprüfte Sicherheit”(tested safety). BA73A fulfills the re-quirements for ergonomy according

Safety InstructionsThis device conforms to the corresponding safety regulations for informati-on technology devices, including electronic office machi

Instructions for MaintenanceInstructions for MaintenanceClean your BA73A regularly with an appropriate surface cleaning product.Make sure that the dev

The BA73A is manufactured without the use of CFCs und CCHS and isproduced mainly from reusable components and materials. The processedplastics can, fo

AppendixAbbreviation IndexASCII American Standard Code for Information InterchangeAT Advanced TechnologyBIOS Basic Input Output SystemCFL Cold cathode

Technical Data ... 48Touch Screen (optional)...

IntroductionFrom Point-of-Sale to Point-of-Service“The customer is king”, a motto that seems so simple and yet it demandsa permanently increasing supp

The low-energy, flickerfree and radiation-free colour monitor of the BA73Ais an Active-Matrix-Display in TFT-technology (Thin Film Transistor).Therefo