Wincor Nixdorf BEETLE /i8A-3 User Manual

BEETLE /i8A-3(D425/D525-Mot her bo ard)Modular POS SystemUser Manual

IntroductionThe BEETLE /i8A-3 is the powerful POS System for multi-functionalsolutions. This entry level POS system unit with low power, state-of-the-

About this manualThis documentation is intended to help you to work with the POS systemand to serve as a reference work. The detailed table of content

Recycling the BEETLE /i8A-3En vi ron men tal pro tec ti on does not be gin when the time has come to dis po se ofthe BEET LE; it be gins with them

WarrantyGenerally, Win cor Nix dorf gua ran tees a war ran ty en ga ge ment for twelvemonths be gin ning with the date of de li very. This war

BEETLE /i8A-3- the POS SystemOverviewYou can connect a variety of peripherals to your modular POS systemBEETLE /i8A-3 and thus implement a wide range

Before switching on the SystemUn pa cking and che cking the Sys temUnpack the components and verify that the scope of delivery is identical tothe info

Ho ri zon tal in stal la ti on Mind the minimum distances indicated below! If the equipment is to befitted, you also must ensure that the specified m

If you install the BEETLE /i8A-3 in vertical position, you have attend to thefollowing:nThree breakable bore holes are located at the underside, which

Cab ling of the BEETLE /i8A-3Follow the steps below in the order given when installing devices:nPlug one end of the power cable into the socket of the

Now push the power ON button on the front side of the system.The power supply can be connected to all conventional power supplynetworks. It automatica

Your opinion:We would like to know your opinion on this publication.Please send us a copy of this page if you have any constructive criticism.We would

The System BEETLE /i8A-3Front Side View ON Button Power LED HDD- LED 2 USB Interfaces Ventilation Slots (NOT COVERING)20 BEETLE /i8A-3 

ON But tonWith a power supplied power unit you switch on the system with the powerON button on the front side of the system unit. Light-emit ting Di

Interior view Power Supply Ventilator RAM Hard Disk22 BEETLE /i8A-3

Power SupplyThe power supply can be connected to all conventional power supplynetworks. It automatically adjusts itself to the particular voltage and

The system is automatically switched off, when the operating system is shut down. Pushing (approx. 5 seconds) the ON button at any time will shutdown

Con nec ting dai sy chai ned cash dra wers and 12V OEM-dra wers ispro hi bi ted!Connect cash drawers only (no telephon).BEETLE /i8A-3 25

System UnitAl ways make sure that the sys tem is swit ched off when you do cab lingworks.Connecting peripherals with the system switched on is not all

12V DC JackThis port is intended to supply 12V power to LCD monitor.Rated current is 3A. If you connect cables to these output connectors for connecti

USB (Uni ver sal Se ri al Bus)- A, USB 2.0You can connect several USB peripheral devices to the USB or poweredUSB interface (12V or 24V).Only con n

D- Sub, 25 pin (LPT1, Modular Printer)The standard parallel interface LPT1 is intended for connecting a printer.D- Sub, 15 pin (VGA)You can connect a

BEETLE /i8A-3(D425/D525 Motherboard)Modular POS SystemUser Manual, Edition June 2012

Dis con nec ting ca blesNever unplug a cable by pulling on the cable; always take direct hold of theplug itself. Follow the procedure below when disc

With HOSIDEN-connector (24VPower supply, e.g. for printer) theplug re mains in ser ted un tilre lea sed. Pull the plastic covering from theconnecti

Storage MediaFollowing storage media are availablenone or two 2.5" SATA- hard disk ornone or two 2.5" solid state disk drive. A solid state

Push the metal plate (1). Tilt the hard disk hol der in direction of arrow (2). Lift up the dri ve and remove it. Loosen the connecting cables.BEETLE

Take the holder out. Loo sen the four Phillips head screws (see arrows) atthe holder with a screwdriver.En su re that you hand le the hard disk with e

C on nect both ca bles to the hard disk. Insert the drive holder.Make sure that the buffers are corresponding to the stampings in the baseplate (see a

P- USB- Hub (optional)There are three 12V P-USB interfaces and one 24V P- USB on an optionalavailable board. They allow the connection of peripherals

COM6*, COM7*- Interfaces (optional)The standard system is configured with four COM* interfaces. In additionexpansions are possible via a com board.Sca

CF- Card Adapter (optional)Optionally the BEETLE can be equipped with a CF (Compact Flash)- cardadapter. The CF is a mass storage device format and us

Starting up the systemAfter installing the BEETLE /i8A-3, switch on the POS system using theON/OFF button on the front panel and the power switch on t

Co py right© Win cor Nix dorf In ter na tio nal GmbH, 2012The re pro duc ti on, trans mis si on or use of this do cu ment or its con tents is not

nHard Disk in drive C:nDVDnLAN module with BOOTPROMnUSB drivePlease mind that the storage medium must be system-boot-capable.If the POS system does no

AppendixTechnical Data BEETLE /i8A-3BEETLE /i8A-3 41DimensionsWidth 310 mmDepth

InterfacesCOMCOM1 (w/o power supply),COM2* -COM5* (with power supply)Optional:COM6*, COM7* via Powered COM HubUSB4 Standard USB (rear), 2 Standard USB

To tal Cur rent Con sump ti on Of In ter fa cesThe total current consumption at 5V interfaces must not exceed 5A.each COM*

GlossaryBitA bit is a binary digit (0 or 1). It is the smallest unit used in data processing.ControllerServes to control data input and output in a da

PCIeAbbreviation of Peripheral Component Interconnect Express. The basis forthe „classical“ bus structure is a parallel architecture, i.e. all connect

AbbreviationsCE European Symbol of ConformityCOM RS 232 Schnittstelle CPU

VDE Verband der Elektrotechnik, Elektronik und Informationstechnik e.V.

Published by Wincor Nixdorf International GmbHD-33094 PaderbornOrder No.: 01750220871C

ContentsMa nu fac tu rer´s Cer ti fi ca ti on...7Tes ted Sa fe ty...

Jack Plug 3.5 mm (IN, OUT, MIC) ...28D- Sub, 25 pin (LPT1, Mo du lar Prin ter)...

Manufacturer´s CertificationThe de vi ce com plies with the re qui re ments of the EECdi rec ti ve 2004/108/EC with re gard to ‘Electromagneticcom pa

nIf this device is taken from a cold environment into the operating room,moisture condensation may form. The device must be absolutely drybefore being

nYour BEETLE sys tem is the re sult of mo dern tech ni cal in no vat ion. Soplea se see for ac cor ding struc tu ral and tech ni cal sur roun d